Inner page banner



Series AC1

Power Factor Corrected
Universal AC Input: 85 - 265 VAC
47 - 440 Hz Input Frequency
Hi Reliability Isolated Regulated
Fixed Operating Frequency: 100Khz
AC-DC Converter to 300 Watts

 

360 to 800Hz Input Frequency
3 Phase Input Available
Consult Factory: 800-431-1064

 

 

Meets EN/IEC 61000-3-2 Requirements
Universal Input Voltage: 85 to 265 VAC
Power Factor Corrected, 0.99 (50 - 100% Full Load)
Space Saving Design: One module replaces two
Special Output Voltages Available
Regulated Output Voltage
Made in the USA, Fully Encapsulated

Typical Features/Electrical Characteristics

AC Line Input Voltage: 85 to 265 VAC 47-440 Hz
Output Power: 150 to 300 watts, see chart

85 - 95 VAC Input, 200w maximum (5V, 150w max.)

Output Voltage Ripple: 75-480 mV, See chart

Operating Temperature: 0 to 85º C, case temperature. See application notes for proper thermal considerations. Availabe with -20°C and -40°C operating temperature range - Consult Factory
Isolation:

  • From Input to DC Output: 4242 VDC
    From Input or DC output to Case: 2121 VDC
    From AC Input to Auxiliary 380 VDC Output: Non-Isolated

Capacitor Requirement: External at Auxiliary 380 VDC Pins: 220uf, 450 Volt Electrolytic
* MUST BE INSTALLED
Current Limit Setpoint: 130 % of full load rating (Typical)
Operating Frequency: 100Khz: Fixed

NOTE: The torque for mounting screws must be 6 to 9 In-Lbs

PIN
No.
FUNCTION
1
AC IN
2
AC IN
3
N/C
4
+380 V BUS
5
-V BUS
6
-V OUT
7
+ V OUT
8
- SENSE
9
+ SENSE
 
 
Pico
Part
No.		 Output
Voltage
VDC		 Max.
Load
Current
(A)
**		 Max.
Output
Power
(watts)
**		 EFF @
Full
Load
(%)*		 Output
Ripple
Full
Load
1-1 MHz BW
mv p-p*		 Out Volt
Toler-
ance
(±%)*		 V Ld.
Reg
10-100%
Load
(±%)*		 Line
Regu-
lation
(±%)*		 Price
(US $)
AC1-5S
5
30
150
76
100
1.0
1.5
0.2
378.27
AC1-9S
9
27.8
250
78
100
1.0
1.5
0.2
378.27
AC1-12S
12
25
300
80
150
0.5
1.5
0.2
378.27
AC1-15S
15
20
300
80
150
0.5
1.5
0.2
378.27
AC1-24S
24
12.5
300
81
250
0.5
1
0.2
378.27
AC1-28S
28
10.71
300
82
300
0.5
1
0.2
378.27
AC1-48S
48
6.25
300
82
500
0.5
1
0.2
416.74

External Capacitor Required:  220µF, 450 V Aluminum Electrolytic Capacitor
*All specifications are typical at nominal (115 VAC, 60 Hz) input, full load and 25° baseplate temperature unless otherwise stated.
** Using proper thermal considerations as outlined in the application notes.

 

CH HEATSINK
CV HEATSINK

All dimensions are in inches  ()=mm
Approx. weight = 145 grams

NOTE:  Additional Heatsink options, consult factory
Approx. Weight = 145 grams

 

 

 
 
 

THERMAL INTERFACE
PART  TI

Alloy Aluminum Substrate

Thermal Conductivity, (BTU-in/hr ft²  ºF) ----1530
Coefficient of Thermal Expansion (25-100ºC, 10-6 in./in. ºF ---13.1
Hardness, Brinnell B ----23
Endurance Limit, psi. ----5000
Standard Thickness (inches) ---.002

Thermal Considerations

  AC1 Series
.
Baseplate
Heatsink
CV
Heatsink CH
Free Air
4.8
3.3
2.8
200 LFM
2.6
1.6
0.9
400 LFM
1.6
1.0
0.6
600 LFM
1.3
0.7
0.5
800 LFM
1.1
0.6
0.4
1000 LFM
0.9
0.5
0.35

 
 

EXAMPLE 1:
An AC1-24S module has an efficiency of 81%. What is the maximum ambient temperature if 100 Watts of power is needed?

 

 

 

 

EXAMPLE 2:
What would be the maximum output power for an AC1-24S module at an ambient temperature of 50°C with an efficiency of 81%?

 

 

 

EXAMPLE 3:
At a maximum ambient temperature of 50°C and an efficiency of 81%, how could an AC1-24S module be used if 200 Watts of output power is required?

 

 

 

 

 

 

For immediate engineering assistance or to place an order:
Call Toll Free: 800-431-1064

PICO Electronics, Inc.

143 Sparks Ave. Pelham, NY 10803-1810
Tel: 914-738-1400
Fax: 914-738-8225